DC Brushless Vibration Motor Controller, 24V

$178.62

DC vibration motor variable speed display controller, 24 volt, maximum current limit 12 amp, speed adjustment by rotating pan

SKU: CHN-VMC-68S-10AD24

Free Shipping Worldwide

Delivery date: 6-12 days

Overview
Documents

Variable speed controller for 24V dc vibration motor, LED display, rated current 10A, small size, light weight, stable performance.

Variable Speed Display Controller Function

Start stop
Potentiometer speed control
Inertial stop
Under-over-voltage protection
Limiting
Overcurrent protection
Locked-rotor protection
Alarm signal output
Speed signal output
No Hall position detection

Specification

Model	CHN-VMC-68S-10AD24
Reated Voltage	20-50VDC
Motor Voltage	24V
Rated Current	10A
Limit Current	12A
Support Maximum Speed	Speed above 20000 rpm, the specific speed depends on the motor itself and the load
Speed Mode	1. Control panel potentiometer: use this potentiometer to adjust the speed 2. External potentiometer: connect the potentiometer to the terminal block behind the controller for speed regulation 3. External 5V speed regulation voltage: Connect 5V speed regulation voltage from the terminal block on the back of the controller
Speed Output	PG signal: There is a 5V speed pulse output between this port and the ground. The output frequency is set to P (Hz), the number of motor stages is N, and the speed is F (RPM), then the output speed frequency: P=F*N/60
Alarm Output	ALM signal: There is an alarm pulse output between this port and the ground 1. In normal operation, this port outputs 5V high level 2. When it is turned on, but the speed control signal is very low and the motor does not rotate, the port signal is low, that is: when the EN enable key is turned on, as long as the motor does not rotate, the alarm port signal is always low , Prompting that the current status is abnormal or there is a question, to be dealt with 3. In the case of undervoltage, overvoltage, locked rotor, phase loss, phase short circuit, etc., the port signal is low level
Forward and Reverse Function	F/R: An external switch is connected to the corresponding position of the rear terminal block, one end of the switch is connected to the F/R port, one end is grounded, the switch is turned on and off, and the rotation direction of the motor can be changed
Start Stop	1. Toggle switch on the panel 2. Connect the switch to the corresponding position of the rear terminal block to control the start and stop Note: The two methods cannot be used at the same time. When using one method, the switch of the other method should be in the on position
Locked Rotor Protection	When the motor is locked, the motor stops working and restarts when the power is turned on
Power Light	Green light: always on when power is on
Status Light	Red light When the boot is enabled, the potentiometer or the external voltage is not turned on, and it is in the semi-standby state, it flashes once at an interval Enable is not turned on, in standby state, flashes seven times at intervals
Insulation Resistance	Under normal temperature and pressure>100MΩ
Dielectric Strength	0.5KV at normal temperature and pressure, 1 minute
Storage Temperature	-20℃～ +65℃
Use Occasions	Avoid direct contact with dust, oil fume and corrosive gases
Operating Temperature	0-45℃
Humidity	<80%, no frost, no frost
Shock	5.9m/S² MAX
Storage Humidity	0~95%RH
Volume	110mm(length)54mm(width)118mm(height)
Weight	0.8kg

24V DC Brushless Vibration Motor Controller Dimension

Vibration Motor Controller Wiring Diagram

DC Vibration Motor Controller Troubleshooting

1. The motor does not rotate.
Check whether the power supply is normal, check whether the wiring of the motor wire is firm and correct, and whether the wiring of the potentiometer is correct and rotated to the correct position.
2. The motor speed is very slow
Check whether the voltage is normal.
3. The alarm LED is always on or flashing continuously
Except for the blinking of standby and semi-standby, check whether the working voltage is normal.
4. Alarm and LED is always on
Check whether the rotor is blocked, check whether there is phase loss, and check whether the phase line is short-circuited.

DC Brushless Vibration Motor Controller, 24V

DC Brushless Vibration Motor Controller, 36V

DC Brushless Vibration Motor Controller, 24V

DC Brushless Vibration Motor Controller, 12V